用途特點:
技術參數

印刷色數: 6色
Printing color: 6 colors
過料寬度：1200mm
Maximum material width: 1200mm
印刷寬度：1160mm
Maximum printing width: 1160mm
機械速度: 140米/分
Maximum mechanical speed: 140 m / min
印刷速度：30-120米/分
Maximum printing speed: 30-120 M / min
套準精度: 縱向±0.15mm(手動) 橫向±0.15mm(手動)
Alignment accuracy: longitudinal + 0.15mm (manual) transverse + 0.15mm (manual)
收放卷直徑: φ1000 mm 收放卷紙筒/膠筒: φ76 mm(內徑)
Retractable coil diameter: Phi 1000 mm retractable roll / glue cartridge: Phi 76 mm (inner diameter)
壓印力: 機械調節
Impression force: mechanical adjustment
起落版: 全自動液壓起落
Landing version: automatic hydraulic lifting and landing
網紋輥：采用陶瓷網紋輥6條
Anilox roller: 6 pieces of ceramic roller.
張力方式：收料/放料 全部采用自動張力檢測系統控制
Tension mode: automatic feeding and discharging system is controlled by automatic tension detection system.
放/收卷方式：采用氣漲軸裝夾料，10公斤磁粉2套，另外配備1臺2.2千瓦電機組合收卷
Release/take-up mode: using air shaft clamping material, 10 kg magnetic powder 2 sets, and equipped with a 2.2 kW motor combination take-up
糾邊方式：自動光電糾邊系統
Edge correction method: automatic photoelectric correction system
干燥方式: 電加熱
Drying method: electric heating
干燥功率: 15KW （特設雙面吹風， 干燥更快）
Drying power: 15KW (special double side blowing, faster drying)
鼓風機: 1.1KW×2個1.5KW×2個
Blower: 1.1KW * 2 1.5KW * 2.
主電機: 5.5KW
Main motor: 5.5KW
主變頻: 變頻器調速
Main frequency conversion: speed regulation by frequency converter
行墨電機: 減速電機（0.2千瓦）
Inking motor: decelerating motor (0.2 kW)
總機功率：35千瓦
Switchboard power: 35 kw
占地面積：長5.8M×寬3.6M×高3.5M
Floor area: long 5.8M * wide 3.6M * high 3.5M
軸承: 日本NSK 單向軸承 德國ASNU 鋁合金導輪 進行硬質氧化、動平衡、靜平衡處理
Bearing: Japan NSK one-way bearing German ASNU aluminum alloy guide wheel for hard oxidation, dynamic balance, static balance treatment
適用范圍：薄膜，無紡布，編織袋，紙張 等
Scope of application: film, non-woven, woven bags, paper, etc.
主要特點說明:
The main features are:
1. 操作簡單放便,套色準確,使用壽命長
1. simple operation, convenient color registration and long service life.
2. 采用馬達,變頻調速,節省電,運行波動小
2. adopt motor, frequency conversion speed regulation, save electricity and run little fluctuation.
3. 落版自動停止行墨馬達，起版自動開始行墨裝置
3. automatic stop inking motor, automatic start inking device.
4. 采用同步帶傳動,印刷尺寸準確,
4. using synchronous belt drive, printing size is accurate.
5. 設有吹風發熱兩套裝置,其中發熱采用恒溫控制系統并分組控制
5. there are two sets of ventilation and heating devices. The central heating control system and grouping control are adopted.
6. 低輥采用特殊鋼材加工，并經過特殊工藝處理,并電鍍10絲厚的硬鉻保護層
6. the low rollers are made of special steel and treated by special process, and electroplated with 10 wire thick hard chromium protective layer.
7 鋁合金導輪進行硬質氧化、動平衡、靜平衡處理
7 aluminum alloy guide wheel for hard oxidation, dynamic balance and static balance treatment.
8 設有冷風定型風箱,能有效地防止印刷后油墨粘連等缺陷
8 equipped with cold air molding bellows, it can effectively prevent defects such as adhesion after printing.
9.印刷圖像清晰 層次感強
9. printing image clarity and strong sense of hierarchy